Giant frames on VSL link

I was checking the VSL link on a network and I have found a lot of giant:

show int Te1/5/5TenGigabitEthernet1/5/4 is up, line protocol is up (connected)
       8 runts, 1739095 giants, 0 throttles

I have searched on cisco.com and I have found the following:
The VSL carries data traffic and in-band control traffic between the two chassis. All frames forwarded over the VSL link are encapsulated with a special 32-byte header, which provides information for the VSS to forward the packet on the peer chassis. 

I guess if a packet close to1500 MTU is received and a 32-byte header is added, we have giant packet. If I'm wrong, don't hesitate to correct me.

VPN connexion and Internet Access

When you are connected to a VPN session, normally you can access to the corporate LAN.
However, it's also possible to have access (in the same time) to Internet.

To do this on ASA, you have to configure some NAT rule.
All traffic that will go to Internet have to use the Internet facing interface like source IP address.

The configuration below is an example that can be applied:

ip local pool Pool_VPN 192.168.40.10-192.168.40.250 mask 255.255.255.0

!

interface GigabitEthernet0/1

 description Outside Facing Interface

 nameif INTERNET

 security-level 0

 ip address 199.199.199.199 255.255.255.240

!

object network NAT-VPN-POOL

 subnet 192.168.40.0 255.255.255.0

 description Pool VPN

!

object network NAT-VPN-POOL

 nat (any,INTERNET) dynamic interface

All traffic with VPN IP Pool source address and with Internet destination will match this NAT rule.
Source address will be modified with the outside interface.

Are you impacted by DNS Changer ?

You can test if you are impacted by the virus DNS changer with the web site below:

http://www.dns-ok.ca/

SUP2T and access to CMP

Just a quick post to talk about the SUP2T and the CMP. CMP (Connectivity Management Processor) is an equivalent of the 'aux' port. On our lab we have decided to test this new feature.
But to access to this interface we need an IP address, but which address ? Maybe, there is DHCP server on this interface ?
We have tested and there is nothing. So we have decided looking for on the cisco web site without success. We have just found on a forum someone who has already encountered this issue.
And, the solution to access to the CMP (and configure it) is to use his default IP which is 192.168.1.101/24 (GW 192.168.1.1).
I hope this will help you. And you will not search everywhere on the cisco web site like us.

Good bye ARP, welcome ICMPv6

Today I was working on an IPv6 lab. I wanted discover the relation between an address MAC and an IP address. So, on the windows machine I execute the command 'arp -a'. It's a bad reflex, why ? ARP no longer exists in IPv6. The equivalent is now realized with ICMPv6. So to discover the correlation between MAC and IP address we have to use these commands:

• On a windows laptop:

C:\Users\Administrator>netsh interface ipv6 show neighbors 14

Interface 14: LAB

Internet Address                               Physical Address    Type
--------------------------------------------           -----------------             -----------
fe80::2                                             00-14-1c-c9-d9-a8    Stale (Router)
fe80::214:1cff:fec9:d9a8                     00-14-1c-c9-d9-a8    Stale (Router)
ff02::2                                              33-33-00-00-00-02     Permanent
ff02::5                                              33-33-00-00-00-05     Permanent
ff02::c                                              33-33-00-00-00-0c     Permanent
ff02::16                                            33-33-00-00-00-16     Permanent
ff02::1:2                                           33-33-00-01-00-02     Permanent
ff02::1:3                                           33-33-00-01-00-03     Permanent
ff02::1:ff00:2                                     33-33-ff-00-00-02      Permanent
ff02::1:ff00:d                                     33-33-ff-00-00-0d      Permanent
ff02::1:ff00:f                                      33-33-ff-00-00-0f       Permanent
ff02::1:ff08:c77                                 33-33-ff-08-0c-77       Permanent
ff02::1:ffae:564d                               33-33-ff-ae-56-4d       Permanent
ff02::1:ffc9:d9a8                               33-33-ff-c9-d9-a8       Permanent  
  

• On a Linux laptop (has to be validated):

ip -f inet6 neigh show

• On a Cisco router:

R2#show ipv6 neighbors
IPv6 Address                                         Age Link-layer Addr    State      Interface
FE80::4491:69A9:39F3:7344                   5     000c.2928.4c53  STALE    Fa0/0
2001:DB9:1:1:DD52:657C:D340:F2FF      19   000c.2980.fc6c   STALE    Fa0/0
2001:DB9:1:1:B140:2298:3E92:A99B       6     000c.2928.4c53  STALE    Fa0/0
FE80::1                                                 4     0016.479a.f630   STALE    Fa0/0
FE80::20C:29FF:FE80:FC6C                  19    000c.2980.fc6c   STALE    Fa0/0
2001:DB9:1:1::1                                     22    0016.479a.f630  STALE    Fa0/0

kron and backup

Today, I have looked my auto archive to see if they work properly. Surprise, all was ok except for the 3560 switch. When someone execute a 'write memory' all work fine but the schedule backup creates an empty file. There are just these four rows:

!

!

!

end

After some investigations on Internet I have discovered that I was not the first to occur this issue with these equipement. So I have decided to use another solution. It's the kron which is the equivalent of the cron on an unix machine. The configuration looks like this example:


archive
path ftp://10.10.10.10/PATH/MY-SWITCH/$h-
write-memory
no time-period 10080
! 
kron occurrence backup at 22:00 25 recurring
policy-list backup
!
kron policy-list backup
cli archive config

I have kept all the configuration of the archive except the 'time-period'. I have just added policy backup which is schedule by a kron. The policy executes the command 'archive config' and the kron starts one time par month every 25th at 10pm. Also, it's very important to have NTP server if you don't want encountered problem to execute a kron.

Add a mount point for an ASA

I have found a nice feature on the Cisco ASA. You can create a mount point to a server FTP.

Below you can find a sample of the configuration to  apply:

mount Backup-ASA type ftp
 server 10.10.10.10
 path /root/Backup
 username  userFTP
 password passwordFT
 mode passive
 status enable

To check all the configuration available on this particular folder you can use the command 'dir':

ASA# dir Backup-ASA:

Directory of Backup-ASA:/

       -rwx  71147       19:37:00 Jul 14 2011  ASA-14jul11.txt
       -rwx  79337       16:41:00 Jan 31 2012  ASA-09-02-2012.txt

0 bytes total (2146293760 bytes free)

This trick can be useful to backup easily the running configuration on remote folder:

ASA#copy running-config Backup-ASA