Windows Automatic Metric for IP routes

I was wondering why sometimes my traffic was going on wireless interface and sometimes on copper interface.
This behavior is due to the automatic Metric feature on windows.
As you can see on the table below if I am connected on a 100Mb, my metric on the copper is 20.


On our site, we have 802.11a/g and 802.11a/g/n access points.

• When I'm on an a/g antenna (max 54Mbps) and a 100Mb copper inteface, I have the following routing table:

C:\Users\ABCD>netstat -rn

IPv4 Route Table
========================================================================
Active Routes:
Network      Destination        Netmask          Gateway       Interface  Metric
0.0.0.0          0.0.0.0        10.1.1.254       10.1.1.32     20
0.0.0.0          0.0.0.0        10.1.2.254       10.1.2.68     25

• When I'm on a a/g/n antenna (and my bandwith is more than 200Mb) and a 100Mb copper inteface, I have the following routing table:

C:\Users\ABCD>netstat -rn
IPv4 Route Table
========================================================================
Active Routes:
Network      Destination        Netmask          Gateway       Interface  Metric
0.0.0.0          0.0.0.0        10.1.2.254       10.1.2.68     10
0.0.0.0          0.0.0.0        10.1.1.254       10.1.1.32     20
As you can see the wireless is preferred with a metric of 10. I have chosen the solution to fix by myself the metric on networks interfaces (copper 1 and wireless 20).

start>control Panel>Network and Sharing Center>Change adpater settings
Right click on the Copper card>Properties>Internet Protocol Version 4>Properties>Advanced
Uncheck 'Automatic metric' and fix the metric

For my case, I'm only using the interface metric. But the result in metric seen with the command 'netstat -rn' is the result of an addition (Gateway metric + InterfaceMetric).
In order to find the gateway metric, you can use the command 'netsh int ip show config':
C:\Users\ABCD>netsh int ip show config

Configuration for interface "Local Area Connection"
    DHCP enabled:                         Yes
    IP Address:                           10.1.1.32
    Subnet Prefix:                        10.1.1.0/24 (mask 255.255.255.0)
    Default Gateway:                      10.1.1.254
    Gateway Metric:                       0
    InterfaceMetric:                      20
    DNS servers configured through DHCP:  10.1.2.5
    Register with which suffix:           Primary only
    WINS servers configured through DHCP: None

Configuration for interface "Wireless Network Connection"
    DHCP enabled:                         Yes
    IP Address:                           10.1.2.68
    Subnet Prefix:                        10.1.2.0/25 (mask 255.255.255.0)
    Default Gateway:                      10.1.2.254
    Gateway Metric:                       0
    InterfaceMetric:                      25
    DNS servers configured through DHCP:  10.1.2.5
    Register with which suffix:           Primary only
    WINS servers configured through DHCP: None

Change phpmyadmin well-know url

In order to access to the web interface of phpmyadmin, by default you have to use the well-know url: mywebsite.com/phpmyadmin.
If you want to change this default url, you can use the following procedure:

• Open the apache.conf file, this file is located in /etc/phpmyadmin (for many Linux servers).

By default, this file looks like:

# phpMyAdmin default Apache configuration

Alias /phpmyadmin /usr/share/phpmyadmin

• Edit the file apache.conf by changing the alias

# phpMyAdmin default Apache configuration

Alias /urlsecret /usr/share/phpmyadmin

• Restart the apache service:

sudo /etc/init.d/apache2 restart